Magnesion

Discussion in 'Water Chemistry' started by Rawdogz, Jul 16, 2008.

to remove this notice and enjoy 3reef content with less ads. 3reef membership is free.

  1. Rawdogz

    Rawdogz Torch Coral

    Joined:
    May 6, 2008
    Messages:
    1,192
    Location:
    Mars

    i think i have been interpeting the reading wrong.

    yes; i start with a full syring, and add solution to the color change,so i use a total of 8ml of reagent C
     
  2. Click Here!

  3. Rawdogz

    Rawdogz Torch Coral

    Joined:
    May 6, 2008
    Messages:
    1,192
    Location:
    Mars
    ok i have to go get some CA and bake soda today
     
  4. Rawdogz

    Rawdogz Torch Coral

    Joined:
    May 6, 2008
    Messages:
    1,192
    Location:
    Mars
    i am going to list all my par later today, so i can get some feed back as to where i need the work
     
  5. Bogie

    Bogie Snowflake Eel

    Joined:
    Feb 7, 2008
    Messages:
    2,350
    Location:
    CT
    Well, your Mag is still fine at 1600 ppm.
    I think you should re-read the instructions and re-test your calcuim and post what you test at.
    If your calcium is still under 400, that's not really a problem if you have fish only and no coral. If you want to keep coral, get it up to ~440ppm.
    Get your dKH up to ~12 dKH. If you add Ca without paying attention to your alk, your alk will drop and your pH will become unstable at much lower alk levels.
     
  6. Rawdogz

    Rawdogz Torch Coral

    Joined:
    May 6, 2008
    Messages:
    1,192
    Location:
    Mars
    retest my
    CA = i used .7ml that make my CA about 330, i would like it to be up around the 440
    Alk = 1.9
    i need to get a dkh kit
     
  7. Bogie

    Bogie Snowflake Eel

    Joined:
    Feb 7, 2008
    Messages:
    2,350
    Location:
    CT
    You can convert alk to dKH.
    But your Alk numbers don't seem right at all, does your kit read Alk in terms of meq/L?
    Typically, 1 °dKH = 17.9 ppm KH
    dKH/2.8 = alkalinity in meq/L

    so
    1.9 x 2.8 = 5.32 dKH. You seriously need to add baking soda or buffer to your tank water ASAP to get your Alk back up to at least over 10, preferably 12 dKH = 4.3 meq/L, according to your test kit. Like I told you, adding Ca would drop your Alk.
     
    Last edited: Jul 22, 2008
  8. Click Here!

  9. Bogie

    Bogie Snowflake Eel

    Joined:
    Feb 7, 2008
    Messages:
    2,350
    Location:
    CT
    About 2 tablespoons of baking soda mixed in water (preferably RO/DI filtered) should raise your 20 gal + 10 gal sump safely back to about 12 dKH.
     
  10. Rawdogz

    Rawdogz Torch Coral

    Joined:
    May 6, 2008
    Messages:
    1,192
    Location:
    Mars
    the test kit i have it the red sea marine aquariums test lab and it reads in meq/l
    the card read it as follow
    0 -1.6 low
    1.7 - 2.8 normal
    2.9 - 3.6 high
     
  11. Bogie

    Bogie Snowflake Eel

    Joined:
    Feb 7, 2008
    Messages:
    2,350
    Location:
    CT
    even high 2.9 meq/L = 8.41 dKH
    and 3.6 meq/L = 10.08 dKH according to the "high" readings.
    If you want to shoot for an Alk of 10 - 14 dKH to support more calcium, then your water will have to read 3.6-5 meq/L Alk. The more calcium you put in, the more the alk will fall and you have to compensate by adding more buffer or baking soda.
    DID YOU ADD IT YET?
     
  12. Rawdogz

    Rawdogz Torch Coral

    Joined:
    May 6, 2008
    Messages:
    1,192
    Location:
    Mars
    yes; mixed and treated, will test the par today and post it