Introducing the new Turbo Algae Scrubber! (Rev 4)

Discussion in 'Turbo's Aquatics' started by Turbo's Aquatics, Sep 3, 2015.

to remove this notice and enjoy 3reef content with less ads. 3reef membership is free.

  1. SkyFire

    SkyFire Clown Trigger

    Joined:
    Jan 31, 2010
    Messages:
    2,009
    Location:
    Sacramento CA
    I'm interested in one of these... looks slick.
     
  2. Click Here!

  3. Turbo's Aquatics

    Turbo's Aquatics 3reef Sponsor

    Joined:
    Aug 4, 2011
    Messages:
    121
    Location:
    West Des Moines, IA
    I've added you to the wait list. I'll be posting the list up as soon as I can get it in decent shape...and probably, on my [skeleton of a] product website
     
    SkyFire likes this.
  4. Turbo's Aquatics

    Turbo's Aquatics 3reef Sponsor

    Joined:
    Aug 4, 2011
    Messages:
    121
    Location:
    West Des Moines, IA
    Well, it took me a while - had to go through tons of emails, multiple threads, PM inboxes, etc...just to make sure I had everyone covered. The list (for L2, L4, L8, and larger) is over 250. That does include a few people who didn't overtly request to be on the list, so that will thin down a bit. I've started contacting people from the top down for the L2 rollout!
     
  5. SkyFire

    SkyFire Clown Trigger

    Joined:
    Jan 31, 2010
    Messages:
    2,009
    Location:
    Sacramento CA
    Cool, thanks.
     
  6. Turbo's Aquatics

    Turbo's Aquatics 3reef Sponsor

    Joined:
    Aug 4, 2011
    Messages:
    121
    Location:
    West Des Moines, IA
    I can't help but throw out this L4 teaser...one major change it not shown (modular growth chamber)

    [​IMG]

    [​IMG]
     
  7. Turbo's Aquatics

    Turbo's Aquatics 3reef Sponsor

    Joined:
    Aug 4, 2011
    Messages:
    121
    Location:
    West Des Moines, IA
    Just an update, it's not often that I get a whole weekend to work by myself in the garage, so I while I did get a ton accomplished, it still wasn't as much as I had hoped. The devil is in the details, and I'm highly detailed. Does that make me my own devil? Anyways, I'm exhausted but before I crash out I wanted to post from progress pics

    Heat sinks drilled & tapped

    [​IMG]

    Example of mounted LED boards and driver for the L2 (there will be 2 sets like this for the L4)

    [​IMG]
    Yes I measured and labelled template wires and sleeves...devil

    One of the very few main body assembly steps - bonding in the J channels (forms a rail for the light fixtures)
    [​IMG]
    Also you can see a stack of slot pipes which were drilled for the screen pin

    Cured Mortar Screens soaking
    [​IMG]

    While we're on the mortar screens I had a little fun with this toy I got the kids a few years back, it's a digital microscope
    [​IMG]

    I had to adjust brightness and contrast of the zoomed in pics, this thing is not a laboratory microscope ya know

    Here is a plain screen (phone + 100x)
    [​IMG]
    [​IMG]

    Roughed up
    [​IMG]
    [​IMG]

    With fresh mortar coating
    [​IMG]

    Mortar after 2-3 days curing in ziplock, patted dry so you can see the rough texture
    [​IMG]
    [​IMG]

    200x
    [​IMG]

    Now that's what I call microscopically rough. It's no wonder this type of screen grows algae lickety split.

    A #4-40 threadcutter
    [​IMG]

    My finger
    [​IMG]
     
  8. Click Here!

  9. Turbo's Aquatics

    Turbo's Aquatics 3reef Sponsor

    Joined:
    Aug 4, 2011
    Messages:
    121
    Location:
    West Des Moines, IA
  10. Turbo's Aquatics

    Turbo's Aquatics 3reef Sponsor

    Joined:
    Aug 4, 2011
    Messages:
    121
    Location:
    West Des Moines, IA
    Some more pictures
    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    Slot pipe is formed to fit into cutout on Growth Chamber so it doesn't rotate. Velcro added for vibration isolation.

    [​IMG]

    The slot pipe come without fittings bonded to it, so you may configure it for the direction of the water source and the connection fittings. A thread/thread union is included as well as a slip/thread straight adapter and elbow adapter, a thread/barb straight adapter and elbow adapter, and an end cap. A slip/slip union is not included. It is important to note that in order to bond fittings to the slot pipe, you must use transition cement (green type) and you must not apply primer to the ABS slot pipe.

    Example configurations

    [​IMG]

    [​IMG]

    [​IMG]
     
  11. Turbo's Aquatics

    Turbo's Aquatics 3reef Sponsor

    Joined:
    Aug 4, 2011
    Messages:
    121
    Location:
    West Des Moines, IA
    Plastic parts and light fixtures (not completed in this pic)

    [​IMG]

    The growth chamber is made of clear polycarbonate and it almost completely indestructible. It has guides molded in for the false bottom (shown in pic above) as well as a barrier separating the main area of the Growth Chamber from the Emergency Drain section. I will also be producing snap-on extensions to this barrier for enhancing 3D growth. The seal extensions have glands (grooves) for holding a total of 4 heavy duty o-rings (3/16" diameter cross section) which provides a dual seal on each drain to ensure no leaking past the seal. The dual o-rings also serve to keep the growth chamber positioned straight up and down within the base for a perfect fit, every time. A small tube of silicone grease (reef safe) is included.

    The bottom of the main section of the Growth Chamber has a draft to it, so that when you shut off the water flow in preparation for cleaning/harvest, the water will not pool on the bottom and then pour out as you maneuver the Growth Chamber out of your sump area. This means you don't have to worry quite so much about holding your hand under that drain extension.

    [​IMG]

    In the above 2 pics you will notice there is a strip of velcro attached to the ends of the Growth Chamber as well as to the inside of the End Cover Plates. This is due to one of those "well, that' didn't turn out exactly as I had hoped" type of things: the End Cover Plates don't lock into the Heat Sink Groove in the base and at the top of the J-channel just quite right. To fix that, I am having this part redone with an offset tab to grab the edge of the J-Channel. Everyone will receive this replacement part when it is ready. Until then, the velcro works to hold the End Cover Plate in position and it is not difficult to remove and replace.

    Here is the underside of the Base - it has ribbing added for structural support against flexing. The ABS may be drilled to secure it to support braces with, for instance, zip ties or nylon thumbscrews.

    [​IMG]

    The base with J-channels bonded in place (comes assembled) showing the Growth Chamber removal access hole. Generally this is not needed, but if you forget to keep the o-rings lubricated or a suction develops between the o-ring seal sections, you might have a little trouble getting it to initially release. Placing your thumb on the edge of the base and pushing up on the growth chamber from below easily breaks the seal so the growth chamber can be lifted up and slid out the end

    [​IMG]

    The pipe extensions match 2" PVC pipe dimensions. Included are (2) 2" x 1.5" slip/slip adapters which can be friction fit or solvent welded (again, using transition cement with no primer applied to ABS Base)

    [​IMG]

    The emergency drain (on end) only need a section of 1.5" pipe extending down to the water level below the unit (just above or no more than 0.5-1" below the water surface). The primary (center) drain will have a valve (not shown) and a detachable bubble blocker. In the past, I used a filter sock hung from the drain handle but this doesn't work extremely well, so I came up with this simple method using a 2" coupler with tapped holes for thumbscrews and a drawstring filter sock (all included)

    [​IMG]

    [​IMG]

    You cut the pipe to length such that the end of the 1.5" pipe is below the water surface (at least 0.5" but not more than 1" - so that it pulls a siphon) then you tune the drain to a full siphon (outflow matches inflow) in order to silence the unit and reduce bubbles (bubbles will be reduced significantly as the screen matures). Then you slide the bubble blocker over the drain and tighten the thumbscrews and cinch the filter bag over the adapter. You can pre-tie the bag so that it slips over the thumbscrews wit little effort, but it won't fall off on it's own.

    There are tons of little details put into this design and I'm sure I'm forgetting many of them!
     
  12. Turbo's Aquatics

    Turbo's Aquatics 3reef Sponsor

    Joined:
    Aug 4, 2011
    Messages:
    121
    Location:
    West Des Moines, IA
    A little clarification about the bubble blocker:

    The primary purpose of the filter sock is not to actually filter, it is just there to help control bubbles from flying around the sump (or tank). Filter socks will trap microscopic baby copepods that fall off the screen, you want these to stay in your tank...so I recommend installing the sock slightly below the water level. Alternatively, you can use it as a filter sock by cinching the bag higher up on the drain. The 2" coupler with thumbscrews creates a gap for water to freely flow out of the bubble blocker at or near the water surface, where the bubble will have more likelyhood of rising to the surface vs getting caught up in the flow towards the return pump.

    At first, with a new screen, bubbles are just flat out hard to control because water falls freely across the screen and entrains air along the way - there is just no good way to prevent this without running all the flow through the filter sock (which is fine to do at first to prevent this - just cinch the sock up higher, around the pipe). But as algae grows and the screen matures, the bubbles will almost completely disappear by controlling the drain with a valve (tuned siphon). I run 3 scrubbers without any filter socks or bubble blockers, and one turns nearly 3000 GPH with a 6" sump water operating level.