Drilling a glass Aquarium.

Discussion in 'Reef Aquarium Articles and How To's' started by Rustynuts, Nov 9, 2008.

to remove this notice and enjoy 3reef content with less ads. 3reef membership is free.

  1. Rustynuts

    Rustynuts Flamingo Tongue

    Joined:
    Feb 20, 2006
    Messages:
    121
    Location:
    Richmond, North Yorks, UK.
    Okay, ever wondered about whether or not to drill your glass tank? How tricky is it, and what to do etc.? Well, in the process of a recent tank build I decided that I would bite the bullet and do it. After all, the worst that could happen was that I'd crack a second hand tank which cost me very little, and if it went well, then I'd learnt a valuable skill. I made the wife take pictures all the way through so I could give a blow by blow walkthrough of how it's done.

    I'm not getting into discussions about where the hole should be drilled or what size it needs to be, as this is a (hopefully) detailed guide to drilling a tank rather than part of a project.

    What you'll need to do this is:

    1. A glass tank (obviously).
    2. A need to drill it (see above).
    3. A diamond tipped glass drill.
    4. A good quality, well balanced cordless drill (no hammer action) with full charge.
    5. The guide plate which comes with the drill (if you buy it from where I did).
    6. A water spray bottle.
    7. Paper towel roll or kitchen roll.
    8. Cup of coffee (optional).


    Ok, first off, where do you buy a glass hole cutter? Answer: - here. Edit: I recently found another supplier who does the drills a lot cheaper. Anchor Tools. Again, this is a UK site.

    I researched all over the web, and asked in local hardware stores etc. (just got a lot of blank looks though), and 365Drills came up as the only place with any sort of product and sales at a reasonable price that you could trust. They sell on Ebay, but I hate that stuff so I went straight to their site. Reasonable prices aswell, and the 55mm drill I bought was delivered to my door next day for less than £30. This drill will be good for about 6 holes if used carefully, so about £5 per hole. I appreciate that this is a mostly American forum, so I don't really know where you can buy over there or how much it'll cost, as I'm based in the UK. But for a guide, I thought £30 for the drill delivered was well cheap.

    This is what it looks like, and you also get the guide plate aswell.

    [​IMG]

    And here's the process from start to finish.

    Use the drill on low speed, slow and steady, and no hammer action. Gentle pressure and let the diamond cutter do the work rather than trying to force it through as fast as possible. The drilling procedure will take 5 - 10 minutes, depending on the thickness of the glass

    What we need.

    [​IMG]

    Siting the guide plate.

    [​IMG]

    A good squirt of clean water for cooling and lubricating.

    [​IMG]

    Starting to drill.

    [​IMG]

    Hold the guide plate in position.

    [​IMG]

    When you get a decent start into the glass, remove the guide plate and spray again with water.

    [​IMG]

    Continue drilling slowly without the guide plate.

    [​IMG]

    Continue drilling, and spray with water occasionally. If you have a steady hand, spray while drilling (or get someone else to spray for you).

    [​IMG]

    Nearly through.

    [​IMG]

    When you're nearly through, support the underside of the glass plug to stop it falling through and cracking the other side of the tank. Paper towelling is ideal (plenty of it). It also stops the water from running straight through the hole and losing the cooling and lubricating process.

    [​IMG]

    There we are.

    [​IMG]

    Lovely job.

    [​IMG]

    Remember, the inside of the hole will have sharp edges where the drilling process finishes. Don't rub your finger round the hole to see what a good job you made of it. Things will go red, and your finger will hurt.


    A good way to look at this is to think that you're not drilling a hole as such, more grinding away the glass to form a hole. Speed is not necessary but a steady hand certainly is, along with clean water to cool the diamond cutter and wash away the ground glass.

    And that's about it. Easy, isn't it? :D
     
    Last edited: Apr 24, 2009
    2 people like this.
  2. Click Here!

  3. getinpora

    getinpora Coral Banded Shrimp

    Joined:
    Oct 13, 2008
    Messages:
    398
    Location:
    Kokomo IN.
    good job!!!! there are some videos on youtube thats shows DIY. keep on reefing. where im at rustynuts is a large car club
     
  4. reef_guru

    reef_guru Humpback Whale

    Joined:
    Apr 4, 2007
    Messages:
    2,753
    Location:
    joliet,il
    you forgot one of the most important parts of drilling into glass:

    here are the minimum requirements in regards to distance for drilling glass
    x = 1.5 t
    y = 4 t
    t = glass thickness

    measurements are taken from the outer most edge of the hole closest to the edge of the glass.

    single hole along side: x from edge
    single hole near corner: x from first edge, y from second edge
    holes next to each other: x from edge, 4t apart
    holes next to each other next to edge: x from first edge, 4t apart, y from second edge

    do not attempt to drill tempered glass
     
  5. Iraf

    Iraf Snowflake Eel

    Joined:
    Jan 20, 2008
    Messages:
    2,389
    Location:
    Tulsa, Ok
    another popular thing if you dont have a super steady set of hands and someone to help spray water, use some plumber's putty around the area to be drilled, build up a wall about 1/2" thick around the area and fill that with water this is used as a cooling tank setup for the bit as it drills
     
  6. grubbsj

    grubbsj Gigas Clam

    Joined:
    Sep 28, 2006
    Messages:
    856
    Location:
    Outside of Seattle, WA
    For the 120g tank that we just drilled, we used a 1" tall piece of 3" pvc and caulked around the base of it with acrylic caulk (just to form a fluid seal) and added 1/4" of cooking oil as lubricant for the drilling processes.... This seemed to work very well as the chip out on the inside was very small and the temp change of the removed glass plug was just above ambient...
     
  7. Rustynuts

    Rustynuts Flamingo Tongue

    Joined:
    Feb 20, 2006
    Messages:
    121
    Location:
    Richmond, North Yorks, UK.
    Hey folks, keep the input coming. I know there are other ways and methods etc. to do this, but this was my method with no prior knowledge or experience, so I know that things can be improved. As a side note, I've since used this method to drill a tank insitu through the side where forming a well for the coolant would not be possible.

    Reef-guru. Yes I know that there are calculations for where the hole should be drilled, and I purposely didn't get into that because I wanted to concentrate on the actual drilling procedure rather than telling people where to drill their holes. Thanks for picking up the baton and running with it on that score. ;)
     
  8. Click Here!

  9. franka12404

    franka12404 Astrea Snail

    Joined:
    Oct 1, 2008
    Messages:
    44
    Location:
    cleveland oh
    I sand blasted a hole in my tank I did not have a drill bit worked great....
     
  10. Camilsky

    Camilsky Montipora Capricornis

    Joined:
    Oct 28, 2007
    Messages:
    1,004
    Location:
    Groningen, The Netherlands
    Very good tutorial! Thanks for sharing! :) K+!
     
  11. baugherb

    baugherb Giant Squid

    Joined:
    Sep 8, 2007
    Messages:
    5,205
    Location:
    southington, ohio
    Great info... Thanks for sharing.. I just paid someone when I need my old nano cube drilled out..
     
  12. Dasco

    Dasco Vagabond Butterfly

    Joined:
    Feb 24, 2009
    Messages:
    1,657
    Location:
    Lowell Mass
    I wanna do this!!