I finally did it.

Discussion in 'I made this!' started by Zgetman, Jun 13, 2014.

to remove this notice and enjoy 3reef content with less ads. 3reef membership is free.

  1. Zgetman

    Zgetman Ritteri Anemone

    Joined:
    Jun 15, 2013
    Messages:
    616
    Location:
    Dumas, TX, USA
    Thank you Mr. Bill. You are very helpful indeed.
     
    Mr. Bill likes this.
  2. Click Here!

  3. Av8Bluewater

    Av8Bluewater Giant Squid

    Joined:
    Aug 27, 2008
    Messages:
    3,401
    Location:
    Dallas
    Yeah that thing is more than strong enough. You got a piece of foam to go under than tank?
     
    Mr. Bill likes this.
  4. Zgetman

    Zgetman Ritteri Anemone

    Joined:
    Jun 15, 2013
    Messages:
    616
    Location:
    Dumas, TX, USA
    No, I didnt think it was necessary. I will have plywood under it.
     
  5. AZDesertRat

    AZDesertRat Giant Squid

    Joined:
    Jul 30, 2009
    Messages:
    3,904
    Location:
    Phoenix AZ
    I never use foam unless the top is not level in all directions or has imperfections, usually 1/2" or 3/4" marine grade plywood is sufficient.

    DIY is at least half the fun of this hobby!
     
    Mr. Bill likes this.
  6. Alfie uk

    Alfie uk Feather Duster

    Joined:
    Aug 24, 2010
    Messages:
    202
    Location:
    Across the pond, England
    Foam or polystyrene sheet will also help absorb shock and vibrations and minimise stress on the fish :)
     
  7. AZDesertRat

    AZDesertRat Giant Squid

    Joined:
    Jul 30, 2009
    Messages:
    3,904
    Location:
    Phoenix AZ
    Thats a new one to me and I have kept saltwater tanks for over 30 years? It might be beneficial for an acrylic tank or even glass tank if the stand top is uneven otherwise I don't see much benefit since the weight is bourne around the edges on a glass tank. Make sure the stand is plumb. level and not racked side to side, diagonally or front to back and its not an issue. I always fill my tanks a few inches, let them sit for a few hours to settle in then level them with shims so they are level in all directions.
     
    Billme likes this.
  8. Click Here!

  9. Billme

    Billme Eyelash Blennie

    Joined:
    Sep 9, 2013
    Messages:
    1,287
    Location:
    Bakersfield, Ca
    I always fill my tanks a few inches, let them sit for a few hours to settle in then level them with shims so they are level in all directions.

    Shims would work. Do you just use the cedar shims like at the depot? How you hide them?
     
  10. Zgetman

    Zgetman Ritteri Anemone

    Joined:
    Jun 15, 2013
    Messages:
    616
    Location:
    Dumas, TX, USA
    I have checked the height of each side and I am just under a 1/4 of an inch short on one corner. I am debating on buying a granite slab for the top, to add a little bit of flare and stability and to ensure there is no warping. I have not nailed the top plywood down yet and I plan on putting a shim on the short side.
     
  11. DBOSHIBBY

    DBOSHIBBY Sleeper Shark

    Joined:
    Jul 27, 2009
    Messages:
    2,557
    Location:
    Detroit, MI
    Foam will not level a tank and should only be used on flat bottom style tanks. Tanks with a rim should sit directly on the wood. If it isn't level shimming the stand is the only way to go. Stand looks great and if I was you I wouldn't have any doubt it will hold your tank. Very nice.
     
    Mr. Bill and Zgetman like this.
  12. Zgetman

    Zgetman Ritteri Anemone

    Joined:
    Jun 15, 2013
    Messages:
    616
    Location:
    Dumas, TX, USA